Bevel Gear Machines

Product Details:

Gleason No. 14 Straight Bevel Coniflex Generator in excellent working condition. The machine is a Double Cam machine which can work in Generation Mode as well as in Format Mode. It is complete with its setting gauges, change gears, operating manual, electrical drawings and lot's of other accessories. The Max. Pitch Diameter of Gear is 24" and the Max. Cone Distance is 12". The complete technical details are as follows -

Make - Gleason (USA)
Model - No. 14
Max. Pitch Diameter of Gear - 24"
Max. Cone Distance - 12"
Max. Face Width - 3.5"
Stroke Length - 0.5" to 4.25"
Max. Pitch - 3 D.P.
Pitch Angle - 5 Degree 42' to 105 Degree 
Extreme Ratio - 10:1
Stroke Rate - 64 strokes/min to 495 strokes/min
- Double Cam Machine suitable for Roughing as well as Finishing.
- Complete with Setting Gauges, Change Gears, and a lot of other accessories.
- Operating Manuals, Electrical Drawings, Nc/75 Table etc. are available.
- Machine is in excellent working condition.

Product Details:

Two tool type Straight Bevel Gear Generator made by Gleason (USA). The model of the machine is No. 12 and it is complete with change gears, mandrels and lots of other accessories. The technical details are as follows -

Make - Gleason (USA)
Model - Number 12
Max. Diameter Capacity - 431 mm (17")
Max. Module - 8.5 module (3 DP)
Extreme Ratio - 10 : 1
Longest Cone Distance - 305 mm (12")
Max. Face Width - 90 mm (3.5")
Max. Length of Stroke - 96 mm (3.75")
- Complete with Change Gears and lots of other accessories.
- Operating Manual and Electrical Drawings are available.
- Machine is in excellent working condition.

Product Details:

Make - Gleason (USA)
Model - No.19
Max. Diameter of Gear - 432 mm (17")
Max. Distance from Center of Gear Spindle to nose of Pinion Spindle - 267 mm (10.5")
Max. Distance from Center of Pinion Spindle to nose of Gear Spindle - 273 mm (10.75")
Max. Offset of Gear Spindle above, or below, center of Pinion Spindle - 76 mm (3")Max. Drive Spindle Speeds - 1200 rpm
Weight of the Machine - 5 tons (approx.)Serial No - 29205- Max. Gear Diameter can be increased with special lapping guards.
- Machine can also be used as a tester.
- Operating Manual & Electrical Drawing of the machine are available.
-  Machine is in excellent working condition.

Product Details:

Make - Gleason (USA)
Model - No. 16
Type - Finisher
Largest Pitch - 2.5 DP
Longest Cone Distance - 9"
Pitch Angle - 5°42' to 84°18'
Number of Teeth - 5 to 200
- Machine can cut both Crown-wheel & Pinion Gear in Generation Mode.
- With Hydraulic Clamping of the Job.
- Automatic Mechanical Teeth Counter; auto-stop after completion.
- Machine is complete with total of 68 change gears (52 Ratio Gears & 16 Cradle Roll Gears) and Cutter Body.
- Machine is in excellent working condition.

Product Details:

Gleason (USA) Number 12-B Straight Bevel Gear Generator in excellent working condition. The machine is a Double-cam type machine suitable for Roughing as well as for Finishing.The technical details of the machine is as follows -

Make - Gleason (USA)
Model - 12-B
Max. Cone Distance - 12"
Max. Face Width - 3.5"
Max. Pitch - 3 DP
Extreme Ratio - 10:1
- Double Cam Machine suitable for Roughing as well as for Finishing.
- With Change Gears and Tool Setting Gauges.
- Complete with it's Operating Manual.
- With Hydraulic Clamping of Job.
- Machine is in excellent working condition.

Product Details:

Gleason (USA) No. 12 Straight Bevel Gear Generator in excellent working condition.This is a Finisher machine and it can work in both -Generation & Format mode. The technical details are as follows -

Make - Gleason (USA)
Model - No 12 Finisher
Max. Diameter Capacity - 431 mm (17")
Max. Module - 8.5 module (3 DP)
Extreme Ratio - 10 : 1
Longest Cone Distance - 305 mm (12")
Max. Face Width - 90 mm (3.5")
Max. Length of Stroke - 96 mm (3.75")
- Machine can work in Generation Mode as well in Format Mode.
- Complete with Change Gears, Operating Manual, etc.
- Machine is in excellent working condition.

Product Details:

Gleason (USA) Number 12-B Straight Bevel Gear Generator in excellent working condition. The machine is a Double-cam type machine suitable for Roughing as well as for Finishing. The predominant feature of the machine is the ability to localise the bearings on the gear teeth. This is achieved by replacing the usual clapper box method of providing relief by a cam controlled,positive advance & withdrawal of the tools.The technical details of the machine is as follows -

Make - Gleason (USA)
Model - 12-B
Max. Cone Distance - 12"
Max. Face Width - 3.5"
Max. Pitch - 3 DP
Extreme Ratio - 10:1
- Double Cam Machine suitable for Roughing as well as for Finishing.
- With Change Gears and Tool Setting Gauges.
- Gleason No 12-B is almost identical to Gleason No. 14 in size, weight & specifications.
- Complete with it's Operating Manual.
- With Hydraulic Clamping of Job.
- Machine is in excellent working condition.

Product Details:

Gleason (USA) Straight Bevel Gear Generator in excellent working condition.The model of this machine is Number 12 and it is a 2-Tool type machine. The technical details are as follows -

Make - Gleason (USA)
Model - Number 12
Max. Diameter Capacity - 431 mm (17")
Max. Module - 8.5 module (3 DP)
Extreme Ratio - 10 : 1
Longest Cone Distance - 305 mm (12")
Max. Face Width - 90 mm (3.5")
Max. Length of Stroke - 96 mm (3.75")
- Machine is complete with Gauge set for Tool setting.
- Complete with Change Gears, Operating Manual, etc.
- Machine is in excellent working condition

Product Details:

Gleason (USA) No. 14 Straight Bevel Gear Generator in excellent working condition.The Max. Pitch Diameter of Gear is 24" and the Max. Cone Distance is 12".The complete technical details are as follows -


Make - Gleason (USA)
Model - No. 14
Max. Pitch Diameter of Gear - 24"
Max. Cone Distance - 12"
Max. Face Width - 3.5"
Max. Stroke Length - 0.5" to 4.25"
Max. Pitch - 3 D.P.
Pitch Angle - 5 Degree 42' to 105 Degree
Extreme Ratio - 10:1
Stroke Rate - 64 strokes/min to 495 strokes/min
- Double Cam Machine suitable for Roughing as well as Finishing.
- With Change Gears, spare cutter holder & some other accessories.
- Complete with it's Operating Manual.
- With Hydraulic Clamping of Job.
- Machine is in excellent working condition.

Product Details:

Gleason (USA) Number 16 Hypoid & Spiral Bevel Gear Generator in excellent working condition. This machine works in Generation Mode and is complete with change gears & Operating Manual.The technical details are as follows -


Make - Gleason (USA)
Model - No. 16
Largest Pitch - 2.5 DP
Longest Cone Distance - 9"
Pitch Angle - 5??42' to 84??18'
Number of Teeth - 5 to 200
- Can cut both Crown-wheel & Pinion Gears in Generation Mode.
- With Hydraulic Clamping of the Job.
- Machine is complete with Change Gears & operating manual.
- Machine is in excellent working condition.

Product Details:

Gleason (USA) make No. 16 Hypoid & Spiral Bevel Gear Generator in excellent working condition. This machine is a Double-Cam machine which can work in Generation Mode and as well as in Format Mode. The technical details are as follows -

Make - Gleason (USA)
Model - No. 16
Type - Double-Cam
Largest Pitch - 2.5 DP
Longest Cone Distance - 9"
Pitch Angle - 5°42' to 84°18'
Number of Teeth - 5 to 200
- The machine can work in Generation Mode & also in Format Mode.
- The machine can cut both Crown-wheel & Pinion Gears.
- With Hydraulic Clamping of the Job.
- Machine is complete with Change Gears & equipped with a Cutter Body.
- Operating Manual of the Machine is available.
- Machine is in excellent working condition.

Product Details:

Gleason (USA) Number 16 Hypoid & Spiral Bevel Gear Generator in excellent working condition. This machine is Finisher which works in Generation Mode. The technical details are as follows -

Make - Gleason (USA)
Model - No. 16 Finisher
Type - Finisher
Largest Pitch - 2.5 DP
Longest Cone Distance - 9"
Pitch Angle - 5°42' to 84°18'
Number of Teeth - 5 to 200
- Cut both Crown-wheel & Pinion Gears in Generation Mode.
- With Hydraulic Clamping of the Job.
- Machine is complete with Change Gears & operating manual.
- Machine is in excellent working condition.

Product Details:

Make - Gleason (USA)
Model - No 12
Max. Diameter Capacity - 431 mm (17")
Max. Module - 8.5 module (3 DP)
Extreme Ratio - 10 : 1
Longest Cone Distance - 305 mm (12")
Max. Face Width - 90 mm (3.5")
Max. Length of Stroke - 96 mm (3.75")
- Machine can work in Generation Mode as well in Format Mode.
- Machine is complete with Gauge set for Tool setting.
- Complete with Change Gears, Operating Manual, Mandrels etc.
- Machine is in excellent working condition.

Product Details:

Make - Gleason (USA)
Model - No 26
Type - Double-Cam
Max. Gear Diameter - 838 mm
Max. Cone Distance (30 degree and 18" cutter) - 419 mm
Max./Min. Pitch Angle - 84Digree18'' / 5Digree42''
Extreme Ratio - 10 : 1
Max. Face Width - 102 mm
Max. Module - 16.9 module
Weight of the Machine - 12 tons (approximately)
- Can work in Generation Mode as well as Format Mode.
- With Hydraulic Clamping of the Job.
- Complete with 3 x Cutter Bodies (12").
- Complete with a total of 79 pcs. of change gears.
- Operating Manual of the machine is available.
- Machine in excellent working condition.

Product Details:

Make - Gleason (USA)
Model - No. 16
Type - Double-Cam
Largest Pitch - 2.5 DP
Longest Cone Distance - 9"
Pitch Angle - 5°42' to 84°18'
Number of Teeth - 5 to 200
- Machine can work in Generation Mode & also in Format Mode.
- Machine can cut both Crown-wheel & Pinion Gears.
- With Hydraulic Clamping of the Job.
- Automatic Mechanical Teeth Counter; auto-stop after completion. 
- Machine is complete with total of 46 change gears (32 Ratio Gears & 14 Cradle Roll Gears) and equipped with Cutter Body.
- Machine is in excellent working condition.

Product Details:

Make - Gleason (USA)
Model - No. 16
Type - Double-Cam
Largest Pitch - 2.5 DP
Longest Cone Distance - 9"
Pitch Angle - 5°42' to 84°18'
Number of Teeth - 5 to 200
- Machine can work in Generation Mode & also in Format Mode.
- Machine can cut both Crown-wheel & Pinion Gears.
- With Hydraulic Clamping of the Job.
- Automatic Mechanical Teeth Counter; auto-stop after completion. - Machine is complete with total of 68 change gears (52 Ratio Gears & 16 Cradle Roll Gears) and Cutter Body. - Machine is in excellent working condition.

Product Details:

Gleason No. 17 Automatic Combination Testing & Lapping Machine in excellent working condition.The machine is designed to Lap and Test Spiral Bevel & Hypoid Gears and the Maximum Diameter of Gear is 432 mm (17"). The technical details are as follows -

Make - Gleason (USA)
Model - Number 17
Max. Diameter of Gear - 432 mm (17")
Max. Distance from Center of Gear Spindle to nose of Pinion
Spindle - 267 mm (10.5")
Max. Distance from Center of Pinion Spindle to nose of Gear
Spindle - 273 mm (10.75")
Max. Offset of Gear Spindle above, or below, center of Pinion
Spindle - 76 mm (3")
Max. Drive Spindle Speeds - 1200 rpm
- Machine can work in Testing Mode as well as in Lapping Mode.
- Driven Head is Vertically Adjustable for Hypoid Gears.
- Operating Manual of the machine is available.
-  Machine is in excellent working condition.